Projects Archives - GabbieGillmer

I could be drinking this! Apec RO-90 Water Filter replacment review.

admin — Mon, 08 Oct 2018 03:00:58 +0000

I really can say this is the most used and best purchase for our home so far. Its the Apec RO-90 Reverse Osmosis under the sink water filter. I was just replacing the filters tonight and I thought I would snap a couple pictures as it looked so gross. I could be drinking all that stuff! Luckily it is filtered out before it gets to our filters water tap. The filter uses Reverse Osmosis to filter out up to 99% of contaminants they say on the website. It stores the water in a tank under your sink and you have a dedicated faucet for it. You have instant access to a large amount of filtered water and it has a fast flow rate.

Disclaimer: This article is not financial advice, or instructions on how you should do anything, it is for entertainment purposes only. This site also uses affiliate links. This means I may make a small amount of money at no cost to you if you buy something after clicking a link on this site.

Now I don’t have any pictures of my husband doing the installation, but he had no problem installing it. He said the instructions were good and it was pretty easy to do. I feel the price for the unit is really reasonable, and the same with the cost of replacement filters. We have to replace the 3 first stage filters every year and they run around 40 bucks for the set. It ends up being much cheaper then using our refrigerator filter for water. (We actually do not use the fridge for water any more) . The other reason we love it is because it fills the glass with water REALLY fast. You get really spoiled with this aspect and waiting for a refrigerator to fill a glass is like watching paint dry now. You can read other reviews HERE and see others have enjoyed it as much as we have.

BEFORE SWAPPING FILTERS

Here is what it looks like pulled out from under the sink and ready to swap filters.

We were almost at our yearly replacement date and I ordered a new set of filters off of Amazon. One thing you may notice from our picture is we have an upgraded first stage sediment clear filter cover as I wanted to be able to see how dirty is gets between filter swaps. Look it this picture, the sediment filter is a pretty ugly brown by now. I was also able tell it was getting close to time to swap out the filters as I could detect the water flow was a little slower on the dedicated water filter faucet the filter uses.

This time I went and ordered 2 sets of the 3 pre-stage filters that get changed yearly. I was able to save 10 bucks and now will have a set on hand for next time. As for price, you can get them direct from Apec or through Amazon. They are usually about the same price, but if your a Prime member at Amazon you save on shipping and get them faster. This was the double pack that saved me a little money.

Here is a picture of the first stage Sediment Filter after removing it. The water had some chunks of stuff floating in it. This is what would be in our tap water.

The carbon filters #2 and #3 did not look to bad when I pulled them out of their containers. The first one #2 had a little discoloration.

THE NEW FILTERS

Getting ready to add the new filters. They just drop in place into the container.

Here is the first stage sediment filter, notice how white they are when they are new. Crazy how dirty the filters end up and all the gunk they pull out of the tap water.

Here is the RO-90 with the clean filters installed and ready to go back under the sink.

While I have never had a leak with the unit, I do have it into a plastic tub under the sink just as a precaution. I guess I am a little paranoid.

We are ready for another year. The other two filters on the unit will need to be replaced in 3-5 years. We plan to do it on our next filter swap as it should be about 5 years. We will just do all 5 filters at once. This full sett next year will run more as the #4 and #5 filters are more expensive. The whole kit of 5 filters was in the 130 dollar range last I checked. But again, this is once every 3-5 years. I think the difference in time depends on the quality of tap water you already have. I always thought we had pretty good water in our location, and I am surprised at how dirty the filters gets.

We purchased our unit directly from Apec Water’s website here https://www.freedrinkingwater.com/ and you can see they do have some optional upgrades. We did a clear sediment filter housing and some 3/8 line upgrade they were offering at the time. They also have some good sales once in a while you can keep an eye out for. If you do decide to make a purchase online through them, They do have a referral program. If you use a friend for the referral they can get a free set of filters. (or you can always use me if you don’t have anyone 🙂 gabbiegillmer@gmail.com

But another great option is to buy it on Amazon HERE. I tend to get the filters on Amazon out of convenience and the free shipping with prime. With Amazons free shipping the price usually seems to be about the same as on Apec’s website. But it doesn’t hurt to check both to see which price is best for you.

Anyways , I really love our water filter and how convenient it is to use. I feel it really is a great product.

The post I could be drinking this! Apec RO-90 Water Filter replacment review. appeared first on GabbieGillmer.

DIY – Lemon Fabric Kitchen Valance and Table Runner

admin — Sun, 30 Sep 2018 23:16:17 +0000

I was wanting to add a little yellow accent to the kitchen and saw this nice tablecloth for 60% off at a local store. I decided to make a Kitchen Valance and a table runner from it.

Starting with a tablecloth.

First I eyeballed the size I needed for a valance, and also for the middle of the table. Then I grabbed my scissors and stitchwitch and my iron. I cut the tablecloth into two pieces to start.

If you don’t know what Stitch Witch is, it looks like this and is a bonding material that bonds upon heat. It will replace my need for any sewing on this project. You can purchase it HERE on amazon.

Here you can see the stitch witch placed down on the fabric, and ready to put fabric over it and Iron.

Just follow the included instructions on the stitch witch and Iron it to bond the fabric together. My Iron was at number 7.

Here you can see it bonded the fabric.

I now have my Kitchen Valance done. I did the same process for the table runner.

Ta da! Here you can see both the table runner and valance hanging up.

Here is a closeup of the table runner.

Here is a closeup of the Valance.

The post DIY – Lemon Fabric Kitchen Valance and Table Runner appeared first on GabbieGillmer.

Ikea Henriksdal Green Dyed Chair covers – DIY

admin — Sun, 30 Sep 2018 22:51:36 +0000

The Ikea Henriksdal Chair covers are really easy to dye to get the color you want. I now have a set of red, black and decided to do a green set. Dying some white Ikea Henriksdal green was next on my list.

Getting started

You can pick up the plain white Ikea Henriksdal chair covers at Ikea, at this link HERE from amazon. Here are mine getting ready to be colored. The covers they are sitting on are my red covers I did earlier.

I prepped the area to keep the stain from getting on anything as I was going to do this indoors. I used some tarps to protect the area in the kitchen.

The Dye I used

I mixed these colors for the project. This time I used RIT Dye (in my last post when I did the Red Chair covers HERE I used dylon brand dye.)

The colors I chose for this batch of Ikea Henriksdal covers was:

BLUE – Rit Evening Blue dye
Yellow – Rit Lemon Yellow dye
Emerald – Rit Emerald dye
Green – Rit Kelly Green dye

I used all four bottles per tub, one of each color.

Protecting my hands was a priority so they didn’t turn green. I used these gloves for this project, you can grab them from amazon HERE.

Needing a way to hold the chair covers down in the ink as they wanted to float to the top, I used some kitchen pots.

One result of being still wet is they look a little darker, but they lightened up after drying.

Drying the covers for just a bit you can see they lightened up, After that I did a hang dry to finish drying them.

Finished the Ikea Henriksdal Green covers.

My new dyed Ikea Henriksdal green covers installed on the chairs 🙂

A closeup shot of the Ikea Heriksdal Green chair cover.

I like changing colors in the room as a fun way to make a quick impact, I really like this option of having sets of separate chair covers in separate colors to go with my mood. This is one of the reasons I like the Ikea Henriksdal chairs so much. In addition to being really versatile, the price is not that bad either. These green chairs ended up being exactly what I wanted for now.

If you want to see more pictures of the red covers, they are shown in this post here.

Thanks for visiting the site! Have a great rest of your day!

The post Ikea Henriksdal Green Dyed Chair covers – DIY appeared first on GabbieGillmer.

Kitchen Island remodel

admin — Sun, 30 Sep 2018 14:57:06 +0000

We recently decided to remodel our kitchen island. Originally it was in an L shape and we wanted it to be just a long straight island. We also wanted to paint it and put on a new countertop. I thought I would go ahead and snap some pictures of the progress.

Starting out

So we had rearranged the existing cabinets to line them up straight. We also removed the existing tile countertop that was on the top. While we wanted to go with a granite countertop, we are holding off on that until we are ready to do all our countertops at once. For now we are going to use a wood countertop we found at Ikea that we liked.

Also you will notice the holes in the cabinet doors below. We did this a while ago when our dog was a puppy. This is where her dog bed is and she sleeps once in a while. She was wondering what I am doing to her house.

It was really easy to cut the new countertop with my a skillsaw. The cut came out nice and clean. The Ikea countertop also has an end piece that we will glue on later, so that the cut end will match the other side.

Here is the back of the island. You can see we needed a longer panel piece for the back after doing the rearrangement of the cabinets. This was fine as we decided wanted to do wainscot on the back as I have always liked the look of it.

So we started by removing the back panel, and also the countertop as it had not been glued down yet. We also removed the doors on the front in preparation of the paint job.

Picking the wainscot

Here we were deciding on a backing. We deiced to go with the narrow lines like the one on the right.

We also got started on the painting while still working on the back. For the paint I went with General Finishes Queenstown Gray Milk Paint as I have used it before. I had to order it from Amazon, but it was worth it as this stuff is amazing and really coats and sticks well to cabinets. Here is a LINK if you want to check it out and read the reviews and see other peoples pictures, last I checked it still had a 5 star rating.

General Finishes Queenstown Gray Milk Paint.

Here is the island with a coat of paint on the front. (And a sad looking dog who is wondering where her dog bed went.)

Next we added a couple more boards to the back to make it easier to attach the wainscot.

Wainscot is now attached and ready for some paint.

Doors and back are painted with the first coat.

Here it is at this stage with no molding on the bottom.

I decided to go with something a little chunkier for the molding then we had on the island earlier. We went ahead and painted it before putting it on the island. In the background you can see the cabinets we purchased for the wall buffet.

I just nailed it with our brad nail gun.

Here is a better overview at this point.

Once the molding was attached I needed to go over and fill the gaps with some paintable caulk.

Here you can see the I just filled in any cracks before the final coat of paint.

Completed

Here is a final overview picture of it completed in the room.

Here is another picture with some yellow accents I added along with some green chair covers I dyed.

And just so you know, someone was really happy to have her little home back 🙂

Thanks for stopping by and checking out the website! Have a great day!

The post Kitchen Island remodel appeared first on GabbieGillmer.

Yellow entry bench painted with Tulip Slick fabric paint.

admin — Fri, 06 Jul 2018 22:12:24 +0000

I just wanted to post a couple pictures of my bench I painted with Tulip slick fabric paint. I really like the color and how it turned out. The bench was one I had added a cushion to in the past and then had stapled on a burlap cover. While I liked the cover, I did not like the feeling of it. So I decided to paint it and see how it turned out.

Disclaimer: This article is for entertainment purposes only. I am not responsible if you try anything on this website and injure yourself or damage your property. This site also uses affiliate links. This means I may make a small amount of money at no cost to you if you buy something after clicking a link on this site.

The project:

This is the paint I used, Yellow Tulip Slick fabric paint. I purchased it off of Amazon.

It took multiple coats to get it to this color. I just like how yellow makes it more cheerful. Also the texture is a lot nicer to touch.

The post Yellow entry bench painted with Tulip Slick fabric paint. appeared first on GabbieGillmer.

Faux wood painted bedroom wall.

admin — Fri, 06 Jul 2018 21:47:12 +0000

My son loves the look of wood and wanted to have some wood panels on his wall. So rather then buy the paneling and go through the hassle I decided to try paining them first. I had seen this technique of using a comb online and it looked pretty good. Here are my results below.

Sorry I don’t have as many pictures as I wanted of the progress, as I just found these on my phone from doing this a couple months ago. I decided to go ahead and post what I had.

The starting point:

Here are the paint colors I used, they were from home depot.

The colors were:

“Baronial Brown” and “Chocolate Heart”

I previously painted stripes on the wall using some extra light blue and Grey paint we had sitting around (Sorry, I don’t have the names of those paints). This was to give a better variance between the boards. Here you can see I had taped off the light blue color so I started by painting over the light brown color with the Baronial Brown. Then I went back and added some splotches of Chocolate heart. For reference the original stripes were about 9-10 inches wide.

As mentioned above started by brushing on the darker Baronial Brown color first and then brushed the light brown over it in splotches. While still wet I ran a comb through it like THESE. You can pick them up at a dollar store. When it came to a point that I wanted to end a board I would just drag the comb down to make a line.

Once I had those planks painted, I waited a couple hours and removed the painters tape to start the planks that were in between the ones I already completed. To paint these I found it easier to use one of THESE things to put on the dark paint straight rather then tape up what I had just painted and risk having issues with the tape on still drying paint.

Again going after putting down some dark using the light brown paint on top, then combing it with a brush to make the wood grain. The more you use the comb, the more the color underneath starts to show.

Here is a closeup of how it looks.

Here is a picture of the final product. I took it with my cell and plan to go back and get a better picture with the good camera.

The post Faux wood painted bedroom wall. appeared first on GabbieGillmer.

Divano Roma Splitback Living Room Sleeper Futon Couch Review

admin — Sat, 09 Jun 2018 17:47:58 +0000

I wanted to do a quick post on the Divano Roma Splitback Couch. It was a pretty good deal as it was under $200 and that included free shipping. It can double as a couch and be folded into a bed if needed.

DISCLAIMER: This is not an instructional post on how to install or put together your product, This is for entertainment only. Please consult with a professional if you do not know what you are doing. I will not be responsible if you injure yourself while doing this, or for any damages you cause. Also this site uses affiliate links, this means we may get a small fee if you buy something through one of these links at no cost to you.

This is the couch that I am reviewing:

Divano Roma Furniture Collection – Modern Plush Tufted Linen Fabric Splitback Living Room Sleeper Futon (Orange)

Here is what you can expect if you order one.

The couch showed up at the door in this large box. It was pretty heavy and took two of us to carry it inside the house.

While the box was big, it did not seem to be large enough to fit the whole couch. I started to wonder if I was missing a box. So we opened it up to find out. We were very careful when using the knife to open so we did not cut into the fabric. On our packaging they did include a piece of cardboard to help prevent this and you can see it in the picture below.

Looking inside I was pretty sure we were missing part of the couch.

Here is the couch removed from the box.

Folding open the couch we could see the extra pieces were hidden in a couple compartments underneath the couch.

Here are the hidden compartments opened. You can see it included the pillows and end pieces.

After pulling it all out we found the bolts and legs to the couch as well.

Here are the 6 legs and bolts. After seeing this, I though this was going to be a breeze to put together.

So starting with the leg’s I did the corner legs first, just a couple Hex bolts and washer’s for each leg.

Then I did the center leg’s. Oh, they also included the needed Hex wrench.

All 6 legs installed on the couch. Only took a few minutes.

Next I flipped it over onto its legs.

Now to attach the end guards. They just slide into these brackets.

One they are mounted the couch looks like this.

One neat thing about this couch is the back has a few different positions. You can go full recline to flat like below. It is about the size of a twin bed.

Here it is with the back of the couch in a recline.

You can even have each side recline separately.

I wanted to get a good closeup of the fabric. Here is about the best I could get. It looks really nice.

Here is a shot of it in the room.

Summary

I think for the price this is an amazing couch. The couch has a pretty firm feeling which I like, but that may detract others. Also the couch is 75 inches in length, but if you measure from the inside of the end pieces it is 68″ (5ft 8″). So if you want to use it as a bed and are taller then 5′ 8″ you might want to pop off the end piece before sleeping (Or lay down at an angle depending on your height.) The end pieces are easy to remove and put back on. I will update this if we have any issues with wear and tear, but so far I am really impressed with the quality for this price. It seems to be a great value. Again the couch can be found HERE

The post Divano Roma Splitback Living Room Sleeper Futon Couch Review appeared first on GabbieGillmer.

Adding a Guitar Wall.

admin — Mon, 30 Apr 2018 01:17:54 +0000

We decided to clean up the floor space a little and put our kids Guitars on the wall. To do this we purchased some guitar wall hooks off of Amazon. Here are a few pictures of putting them up and how we did it.

DISCLAIMER: This is just how I mounted my Guitar hooks, not an instructional on how you should do yours. Your situation may be different then mine. Please consult with a professional if you do not know what you are doing. I will not be responsible if you injure yourself while doing this, or for any damages you cause. Also this site uses affiliate links, this means we may get a small fee if you buy something through one of these links at no cost to you.

The project start:

We purchased these hooks off of amazon. It was a box of 8 hooks. We only planned to use 6 of them for now.

Here is a picture of the brand and box. It was 8 Guitar Wall hooks and a couple pick holders.

Here is what was in the box.

Each hook is comprised of the base and hook portion. They even provided the wall anchors.

I started by just screwing the hooks to the base.

Here is the back of the base.

Next I found the studs in the wall with my stud finder, as I wanted to make sure I had at least one screw in each stud. I was spacing them ~16 inches apart. I was also alternating height at 14″ from the ceiling and 20″ from the ceiling. As a precaution I made sure my marks were 16 inches apart which is a common spacing in the US. I have not done this in the past and hit a water pipe thinking it was a stud. That was not a fun lesson. Below you can see I was using a single sheetrock anchor and the other two holes were going to be into a stud. I just predrilled my hole for my anchor and tapped it in.

Here you can see how I was alternating the height between holders. While I could have used the included screws, I had some heavier duty ones handy that I chose to use if going into the stud.

They were pretty easy to mount and the 16″ spacing worked well for both Electric and acoustic guitars side by side.

All six hooks up, Room for a new guitar soon!

One more picture.

Thanks for visiting!

The post Adding a Guitar Wall. appeared first on GabbieGillmer.

DIY – Dyeing IKEA Henriksdal chair covers red.

admin — Tue, 17 Apr 2018 04:39:12 +0000

The Project:

I wanted to add a little color to the kitchen recently. I was looking around for some Red chair covers for my IKEA Henriksdal chairs. I wasn’t having much luck finding any so decided to make my own. I had heard people had good luck Dyeing IKEA chair covers, so I decided to give it a try.

Disclaimer: This article is for entertainment purposes only. This site also uses affiliate links. This means I may make a small amount of money at no cost to you if you buy something after clicking a link on this site.

Basically I started off with a trip to Ikea and picked up some of the plain white Henriksdal covers. They tend to always have these in stock and the price is reasonable. You can also purchase them on Amazon HERE. ( I was thinking about buying a few extras and trying a tie-dye multi color design for fun. Maybe let the kids design their own chair cover. If I do this I will add another post. )

This is the Dye I used along with links. Basically I put two Tulip Red packets and one Rosewood Red packet in each buckets I used for the project. I followed the instructions on the back of the packet, it was really simple.

Making a mess

As I was soaking the covers I noticed they kept trying to pop up and would not stay covered with the dye. I tried to get the air bubbles out but the covers still tried to float. So I ended up using pots to weigh down the seat covers.

Even with the pots on them, I still had to periodically poke them back into the dye. Once done I followed the instructions on the back of the dye packet and did the wash and dry.

Here is the final product. I was very pleased with how they turned out. And I didn’t get any dye on any other surfaces. Success!

This is what it looks like with the chairs around the table. It gives that pop of color in the kitchen i like.

Someone else sure likes them!

Here is a link to some more covers I dyed green – LINK

The post DIY – Dyeing IKEA Henriksdal chair covers red. appeared first on GabbieGillmer.

DIY – Kitchen wall cabinet buffet.

admin — Sun, 15 Apr 2018 23:28:14 +0000

The Project:

Here are some pictures of our new kitchen wall cabinets. We had added some 12″ cabinets to the upper wall, but decided we wanted to add some 12″ cabinets to the floor as well and make a buffet. One of the problems we found is that the standard 12″ cabinets from Lowes and Home Depot do not have a base on them. So we decided to buy them anyways and just add our own base.

Here is the starting point. You can see the existing 12″ cabinets on the wall. We wanted a 12″ buffet against the wall below it.

This is the starting point. Only the 12″ cabinets on the wall.

Quick trip to home Depot and Lowes and we found that all of the unfinished 12″ cabinets did not have a base, they were meant to be hung on the wall. This is where we decided to just get them and build our own base.

12″ cabinets all had no base.

So we loaded the cabinets up and headed home. We bought 2qty 30″ wide and 3qty 12″ wide.

Picking up the cabinets.

Now that they were home, we were ready to put on a quick coat of stain.

Ready for Stain.

Here you can see I started staining them. I used MinWax Colonial Maple 223.

For the stain we used Min Wax Colonial Maple 223.

Here is a picture of the cabinets with a light coat of stain. You can see how short they are when they are sitting against the wall. Now I need to get the base built.

Cabinets with no base.

To start the base, I just used a skill saw to cut some wood for the base. I think I had to go with 1″ x 6″ as I did not see any 1″ x 5″ boards available.

Used the miter saw to cut the base boards.

I started cutting the base boards and put one on each end of a cabinet. For the 30″ cabinets I also put a brace in the middle.

Adding base boards

Then I added a kickboard to the front. I plan to use another finishing board to cover it all up as there will be a gap between cabinets.

Adding front boards

Just a close-up picture of the front boards. I used my brad nail gun to put the boards on.

Base Boards attached

You can see the height is much better with the base boards attached. Now I just need a counter top.

Cabinets with base attached

Next I anchored the cabinets together so they line up nice and even. I used clamps to hold them in place and then screwed them together.

Attaching cabinets to each other.

I did not use any glue, I decided to just screw them together. I did drill a pilot hole first.

These are the screws I used in case you were wondering.

Screws to attach cabinets to each other.

One down, many to go. I used 3 screws per side.

Here is a shot of all the cabinets attached.

Here is what the base looks like a little closer up. It is ready to be finished with a face plate.

Close-up of the base.

Now for the cabinet counter top, we just picked out a laminate top from Home Depot. I should have snapped a picture of it before I put it on. Basically it was way to wide, so I had to use the skill saw to narrow it to our requirements. I just drew a line down the countertop and cut it with the skill saw by hand as I do not own a table saw. It was really easy to cut. Here you can see it after I cut it.

Counter top added

Now I need to do the kickboard and side faceplates. And also glue down the countertop. That will be coming next… .

The post DIY – Kitchen wall cabinet buffet. appeared first on GabbieGillmer.